The NPU is in Installer Mode |
To leave Installer Mode set the NPU Address to one, either manually on the module or using the button below |
Ideally you want your setpoints or thresholds for this sensor in the middle of its range.To achieve this your can change the input range of the sensor. | |
The sensor input is not within the scaled input range.
Are you sure you want to accept this scaled range?
This module is not in Standard DALI mode and cannot be commissioned using this page. Use Advanced DALI Management to commission.
Ballasts unique identifiers are matching, but the ShortAddresses have been edited outside of the eDIN configuration. Either Apply to restore ballasts to their last known configuration or Restart find to start over.
One or more ballasts have a lamp failure. Replace the faulty lamp bulb(s).
You must remove missing ballasts before being allowed to proceed with commissioning the new ballasts.
You must add all new ballasts to the current configuration and apply the changes before being able to assign them to channels.
There are currently more than 64 live ballasts on the bus, you must fix this issue before being allowed to proceed with commissioning.
There are currently no live ballasts on the bus, you must fix this issue before being able to proceed with commissioning.
An error occured whilst trying to find ballasts, please check the wiring of the DALI bus and retry.
Some ballasts have bad ShortAddresses, preventing the commissioning proceeding. You may need to use Advanced DALI Management or use 'Wipe all ballasts and re-find' to resolve this issue.
DALI Ballasts Data | ||||
---|---|---|---|---|
Short Adr | Type | Groups | State |
There are currently more than 64 live ballasts on the bus, you must fix this issue before being allowed to proceed with commissioning.
There are currently no live ballasts on the bus, you must fix this issue before being able to proceed with commissioning.
An error occured whilst trying to find ballasts, please check the wiring of the DALI bus and retry.
Some ballasts have unassigned or duplicate ShortAddresses, preventing the commissioning to proceed normally.Either manually fix or use Commissioning tasks to resolve this issue.
There is no commissioning data. Accept ballasts to import their data.
DALI Fixture Data | |||
---|---|---|---|
Channel | Expect | Found |
<%~channelName%> | Number of fixtures found:<%=newExpected%> |
Is this correct? OK to accept |
<%~channelName%> | Number of expected fixtures:<%=expected%> |
You are resetting the expected fixture count to zero and turning off runtime channel monitoring. Are you sure?
Is the ballast you're looking for at <%=ballastLitLevel%>% ?
You have selected ballast on address <%=address%>.
Ballast on address <%=address%> can not be located and assigned if it can not be lit.
An error occured whilst programming the ballast data, please check the wiring of the DALI bus and retry.
This operation will clear your current ballast configuration, are you sure you want to proceed?
This operation will clear your current ballast configuration. Are you sure you want to proceed?
This operation may clear your current ballast configuration. Are you sure you want to proceed?
Expected | Actual | |
Long Address | <%=knownDevice.LongAddress%> | ><%=foundDevice.LongAddress%> |
Short Address | <%=knownDevice.ShortAddress%> | ><%=foundDevice.ShortAddress%> |
Device Type | <%=eDIN_DaliTypeValueToString(knownDevice.DALIDeviceType)%> | ><%=eDIN_DaliTypeValueToString(foundDevice.DALIDeviceType)%> |
Groups | <%=knownDevice.Groups%> | ><%=foundDevice.Groups%> |
Status | <%=eDIN_DaliStatusValueToString(foundDevice.DeviceStatus)%> |
This operation will assign a new short address to this ballast. If the new short address is already in use by another ballast, the ballasts will swap short addresses. |
Select the file you want to upload into the network processor and press the Ok button. The new commissioning data will be imported.
Please note that this operation CAN NOT be undone.
Save the following information to your local hard drive.
DALI Commissioning Data | _dali.csv | (Export the DALI commissioning data in your configuration as a CSV file.)] |
This operation will clear the DALI commissioning data for ALL UBC modules in your configuration.
It will also perform a 'Refresh All' operation to refresh all modules.
<%} else {%>This operation will clear the DALI commissioning data for this UBC module.
You will need to refresh the module with Refresh Ballasts Data.
<%}%>Are you sure you want to proceed?
Please note that this operation CAN NOT be undone.
Exporting the <%=FileType%> configuration file failed for the following reason:
<%} else {%>Importing the <%=FileType%> configuration file failed for the following reason:
<%}%><%if(ExportFlg) {%>Please retry again or contact Support for further assistance.
<%} else {%>Please retry with another valid file or contact Support for further assistance.
<%}%>This operation will start a refresh operation on ALL UBC and COUT modules in your configuration.
This operation may take several minutes to complete.
Are you sure you want to proceed?
Waiting for all modules to refresh
Determining universes and channels still refreshing.
Let the system know that DALI Commissioning has finished and it can re-enable runtime status checks.
DALI Commissioning is an Advanced operation. |
If done incorrectly you can DAMAGE your lighting system. |
Do NOT proceed unless you have been trained in how to perform DALI Commissioning on eDIN+ systems. |