The current INT232 hardware only supports 8 data bits, 1 stop bit and optional parity.
NOTE: set time to become inactive in Config-Options -> Parameters -> Inactive plate delay
Note: set all relay channels to switched or linked
Note: Change colours using the Adjustments page
To accept channel enable click 'OK', then re-enter to adjust the channels settings.
This is a linked channel. You cannot identify it.
This is an input channel. You cannot identify it.
This will remove the channel from all scenes and remove all actions from this channel.
Are you sure you want to delete this channel?
Are you sure you want to delete this?
No days selected means days filter disabled which is the same as All days selected
NOTE: The "0" or "END" state is special and is used as the "OFF" state.
Add PIR channels to strongly link and control this occupancy area as a single area. This is the equivalent of linking PIR channels together.
Link areas to weakly hold this occupancy area on. This area is held as occupied when one or more of the linked areas is occupied. But the linked areas are independent of this area.
Link system modes to hold this occupancy area on. This area is held as occupied when one or more of the linked system mode's state is not zero.
Link sensors to hold this occupancy area on. NOTE: This occupancy area does NOT control the linked multisensor state.
There are errors in this dialog. Fix the errors and try again, or cancel the dialog.
Select which days you want for this new timeline.
Note: These days will be removed from all other timelines in the same Weekly Timeline group.
You cannot delete the last timeline. There must be at least one timeline.
Are you sure you want to reset module colours to their default values?
Select which DMX zones to apply this live colour to
There are no zones selected
Note: Deleting this area will move everything in to the Default area
Are you sure you want to delete this area? All scenes and channels in this area will be moved to the Default Area.
This area's name is already in use. Do you want to merge these areas?
This area's name is already in use. Please change the name and try again.
You cannot add an area that has a blank name. Please change the name and try again.
Area Tagging can be useful for large sites to define Zones and to allocate areas to these Zones. You can then view the site by Zones.
Areas can be put in to no Zones, one Zone or more than one Zone.
When enabled the Default Area Tag is automatically added to every area of the configuration.
Area tag names must not be blank.
There are no areas defined.
This operation has failed for the following reason: <%=message%>
Please retry again or contact Support for further assistance.
Note: The speed the channels are adjusted by is determined by 2 parameters: (a) this scene adjustment step size and (b) the input channel's reporting period.
Are you sure you wish to exit without saving ?
Programming Scene Settings. Please wait
The system must be inactive while this is happening. Make sure No plate buttons are pressed during this programming.
The sensor input is not within the scaled input range.
Are you sure you want to accept this scaled range?
Loading Data. Please wait
The current configuration was not created using the online configuration editor
This Network Processor is not the current Master.The current Master is on MBus Address <%=MasterAddress%>.This Network Processor is on MBus Address <%=Address%>.
<%=undolist%>
Select the files you want to upload into the network processor and press the Ok button. The new configuration will be loaded. If this configuration is password protected, you will need to logon again to be able to edit it.
Please note that this operation CAN NOT be undone.
Importing the file:<%=filename%> failed for the following reason: <%=message%>
Please retry with a valid file.
Select the files you want to import into the network processor and press the Ok button. The files will be loaded.
Downloading in progress. Please wait.
Uploading in progress. Please wait.
Exporting the <%=FileType%> configuration file failed for the following reason:
Importing the <%=FileType%> configuration file failed for the following reason:
Please retry with another valid file or contact Support for further assistance.
Please confirm that only want to save the modules and plates and you don't want to save everything else in your configuration.
Save the following information to your local hard drive.
Select the hardware and quantity you want to add and press the Ok button
You have selected the following hardware
<%=hardwarelist%>
Are you sure you want to add all this hardware?
You are about to clear the configuration.
Rebooting System. Please wait
User Accounts are enabled.
There are 0 user accounts defined excluding Guest and Administrator
To disable User Accounts remove the configuration password. NOTE: This will delete all user accounts.
To enable User Accounts set a non-blank Configuration password.
You are about to delete the configuration password whilst there are still users defined. This will delete All users too. Are you sure?
To enable User Accounts you must also set a valid Administrator password. You can change this administrator password later in the Settings page.
There are unsaved changes on this page.
[(Choose])Revertto loose these changes.
[(Choose])Applyto save these changes.
Applying changes. Please wait
The system must be inactive while this is happening.